RIDGE & HIP
AC-01
Ridge & Hip Caps
Profiled caps that close the roof peak and hip lines while allowing controlled ventilation.
Bond / Shingle / RomanVentilated optionColour matched
Roofing Accessories / Rainwater & Fixings
The small parts that keep a roof watertight.
Ridge caps, hips, valleys, flashings, closures, fasteners, ventilation and rainwater components — profiled and coloured to match the exact tile and drainage system on your roof.
0Matched accessory range
0Component families in stock
0%Profile & colour matched
0Unmatched trims on site
1PROFILE MATCH
Compatibility
Specified as a kit, not a loose list
Most roof leaks start at a junction, not in the middle of a sheet. We issue the accessory list together with the tile and drainage take-off, so every ridge, valley, penetration and eaves detail has a matching part before installation starts.
- Accessories cut to the exact tile profile
- Same coating and colour batch as the roof sheets
- Fastener and sealant quantities included in the take-off
- Rainwater parts coordinated with the PVC drainage range
Component range
Six families of finishing parts
Every part is selected against the roof profile, pitch and drainage layout of the project.
RIDGE & HIP
VALLEY
AC-02
Valley Trays & Flashings
Pre-formed valley trays, apron, barge and sidewall flashings for every penetration.
Pre-formedApron / bargeSidewall
FIXINGS
AC-03
Screws, Closures & Sealants
Matched fastener sets with EPDM washers, foam closures and neutral-cure sealants.
EPDM washerCorrosion ratedCorrect length
RAINWATER
AC-04
Gutters & Downpipe Parts
PVC gutters, stopends, brackets, outlets and downpipe fittings that tie into the QB Roof drainage range.
200 / 250 / 300 mmBracket setsDN matched
VENTILATION
AC-05
Vent & Skylight Kits
Ridge vents, turbine vents and skylight flashings for a ventilated, dry roof space.
Ridge ventTurbine ventSkylight flashing
SAFETY
AC-06
Snow Guards & Walkways
Snow retention, anchor points and roof walkways for safe maintenance access.
Snow guardAnchor pointWalkway
Compatibility
Which part goes with which system
Use this matrix as a starting point. A project-specific accessory schedule is issued with every quotation.
| Parameter | Typical value / option |
|---|---|
| Stone coated roof tiles | Ridge / hip caps, valley trays, barge & apron flashings, closures, screw sets |
| PVC-U drainage | Gutters, stopends, brackets, gutter outlets, downpipe fittings, leaf guards |
| Light gauge steel framing | Base plates, bolt sets, bracing straps, purlin cleats, anti-corrosion tape |
| Ventilation | Ridge vent, turbine vent, eaves vent strip, skylight flashing kit |
| Fastener specification | Selected by substrate (steel / timber), tile profile and wind zone |
| Packing | Accessories packed and labelled by roof zone to match the installation sequence |
* Indicative values for illustration. Confirm the current certified data sheet, test reports and project-specific requirements with the QB Roof engineering team before specification or order.
Why it matters
No missing parts. No site improvisation.
Watertight details
Factory-profiled junctions seal correctly the first time, with no cut-and-fold work on site.
One colour batch
Trims and sheets are supplied from the same coating batch for a consistent finish.
Faster fixing
Zone-labelled packs mean the right part is on the right part of the roof.
One responsibility
A single supplier signs off the tile, trim and drainage interface together.
In detail
Accessories & rainwater parts
AccessoriesQB Roof accessory and rainwater range
ProfilesRidge, valley and gutter profile matching
DrainagePVC rainwater components
SupplyPacking and quality check
InstalledFinished roof with matched trims
Send us the roof plan
We will return a complete accessory schedule — including fixings, sealants and rainwater parts — with your quotation.
Explore the range