GUTTER
PV-01
Double-Arm Gutter
The main 5.2″ double-arm gutter profile, supplied in 3.98 m lengths. Carries water along the eaves to each drop outlet.
5.2 inch3.98 m length6+2 pcs/ctn
5.2″ PVC Rain Gutter System / 14 Matched Components
Rainwater, channelled
Rainwater, channelled
from eaves to ground.
A complete 5.2″ PVC gutter and downpipe system — double-arm gutter, drop outlets, downpipes, elbows, corners, joiners, clips and end caps. One matched profile, one bill of quantities.
0Matched component SKUs
0Standard colour options
0Component categories
0Complete take-off per project
Interactive system
Six points of a gutter run
Select a numbered point on the assembly drawing to see what it does, which components we supply and what to check at design stage.
Schematic assembly — component positions are indicative. The drawing is interactive on desktop and mobile.
01
Eaves & gutter line
The gutter run is set out along the eaves with the correct fall to each drop outlet. Hanger spacing and outlet positions are fixed before any components are ordered.
5.2″ profile3.98 m lengthsFall to outlet
Ask about this component 02
Drop outlet
The drop outlet is the transition from the gutter into the downpipe. One outlet is placed at every downpipe position along the run.
Square waterway40 pcs/ctnProfile matched
Ask about this component 03
Gutter joiners & corners
Inside and outside corners turn the gutter at the building perimeter; joiners connect standard 3.98 m lengths into one continuous sealed run.
90° cornersGutter joinerEnd caps
Ask about this component 04
Downpipe & bends
The rectangular downpipe carries water to ground level. 90° and 65° elbows and diverters route it around eaves, returns and projections.
3.98 m lengths90° / 65° bendsDiverters
Ask about this component 05
Clips & hangers
Pipe clips fix the downpipe to the wall; internal hangers support and level the gutter along the fascia.
Pipe clipGutter hangerBracket spacing
Ask about this component 06
Discharge & handover
The final downpipe section connects to the site drainage. A complete component take-off and packing list is issued with every quotation.
Site dischargeTake-off listCarton packing
Ask about this component Component range
Fourteen parts, one matched system
Every part is profiled for the same 5.2 inch gutter and downpipe. Standard lengths, pack rates and unit weights come from the current product list — no mixed tolerances and no missing trims on site.
GUTTER
DOWNPIPE
PV-02
Downpipe
Rigid rectangular downpipe in 3.98 m lengths, matched to the drop outlet and the full elbow / connector range.
3.98 m length6 pcs/ctn2,664 g
OUTLET
PV-03
Drop Outlet
Gutter-to-downpipe transition with a square waterway. Fitted at every downpipe position along the gutter run.
Square outlet40 pcs/ctn338 g
FITTING
PV-04
90° Elbow
90° downpipe direction change. Ribbed bend with a matched socket collar for a flush joint.
90° bend80 pcs/ctn150 g
FIXING
PV-05
Pipe Clip
Fixing clip that secures the downpipe to the wall at the designed bracket spacing.
300 pcs/ctn33 gDownpipe fixing
CORNER
PV-06
90° Outside Corner
External 90° corner that turns the gutter around the outside of the eaves line.
90° external38 pcs/ctn320 g
FITTING
PV-07
Pipe Connector
Socket connector that joins downpipe lengths and fittings into one continuous run.
96 pcs/ctn85 gSocket joint
CLOSURE
PV-08
End Cap
Pair of end closures that seal the terminal ends of a gutter run.
Pair33 pairs/ctn275 g
CORNER
PV-09
90° Inside Corner
Internal 90° corner for the inside turn of the eaves line; profile-matched to the gutter.
90° internal30 pcs/ctn384 g
FIXING
PV-10
Gutter Hanger
Internal hanger bracket that supports and levels the gutter along the fascia.
220 pcs/ctn33 gGutter support
JOINT
PV-11
Gutter Joiner
Profile-matched joiner that connects two gutter lengths with a sealed joint.
75 pcs/ctn110 gLength joint
FITTING
PV-12
65° Elbow
65° offset bend for downpipe runs that need to clear eaves, projections or wall returns.
65° bend125 pcs/ctn150 g
FITTING
PV-13
65° Diverter
65° branch / diverter fitting for the downpipe run.
65° branch96 pcs/ctn150 g
FITTING
PV-14
90° Diverter
90° branch / diverter fitting for the downpipe run.
90° branch72 pcs/ctn165 g
Technical data
5.2″ system specifications
The values below describe the standard gutter and downpipe range supplied by QB Roof. Confirm the current data sheet and the packing list with your quotation.
| Parameter | Typical value / option |
|---|---|
| System | 5.2″ PVC rain gutter & downpipe system |
| Gutter profile | Double-arm, 5.2 inch |
| Standard length | 3.98 m per gutter / downpipe length |
| Downpipe | Rectangular section, 3.98 m lengths |
| Standard colours | Light Brown / White / Dark Grey / Black |
| Component range | 14 matched SKUs: gutter, outlet, pipe, bends, corners, joiners, clips, caps |
| Packing | Carton packed; per-SKU pack rates shown with each component |
| Unit weight | 33 g to 3,800 g depending on component |
One matched profile
Gutter, corners, joiners, outlets and downpipe are all made for the same 5.2 inch section, so the run closes without adaptors.
- 14 matched SKUs
- No mixed tolerances
- Complete take-off
Four stocked finishes
Choose Light Brown, White, Dark Grey or Black to coordinate with the roof and fascia. Colour samples are available on request.
- 4 standard colours
- Colour-matched parts
- Lightweight PVC
* Values reflect the current standard product list. Confirm the current data sheet, colour availability, pack rates and project-specific requirements with the QB Roof team before specification or order.
Colour options
Four stocked finishes
Gutter and downpipe sections are supplied in four standard colours. The same finish is carried across the corners, joiners, outlets and fittings so the whole run stays consistent.
Light Brown
White
Dark Grey
Black
Colour appearance on screen may differ from the finished product. Request physical samples before placing an order.
Ordering support
A complete take-off, not a box of loose parts
011
Eaves layout
Roof plan, eaves length, corners and downpipe positions.
022
Component take-off
We map the 14 SKUs to your run: gutter lengths, outlets, bends, joiners, clips and caps.
033
Colour & packing
Confirm the finish, pack rates per SKU and the final carton list.
044
Delivery & site support
Zone-labelled packing, delivery schedule and installation guidance.
In detail
Components & assemblies
Drop outletDrop outlet — internal and external views
FixingsPipe clip and internal gutter hanger
Elbow90° ribbed elbow and socket
Corner90° gutter corner, two-piece assembly
ConnectorDownpipe connector and sleeve
OutletGutter-to-downpipe transition
OutletDrop outlet side view
OutletDrop outlet, inner face
ProfileRibbed PVC profile sample
InstalledGutter and downpipe installed at the eaves
Send us the eaves layout or roof plan
We will map the 14 components to your gutter run, confirm colours and pack rates, and return a complete take-off.
Explore the range